Edwards nEXT200200 Скачать руководство пользователя страница 20

Страница: 20 / 100

2.4.5 Controller configuration (serial configuration)

All configuration settings stored in the motor controller are kept when the power to the

pump is removed so that it is possible to use another system to configure the motor

controller before the installation of the pump at the application. You can configure the

operation of the pump as per the application and the pump can be operated using a

simple parallel interface system.
To configure the pump, use a customer simple serial system or use the

manufacturer's TIC Turbo Controller or Turbo Instrument Controller. The TICs allows the

storage of a pump's configuration. You can download the configuration to another

pump. This is useful when you configure a number of pumps with the same settings

before they are installed at a system.

Note:

The RS485 / RS232 slide switch must be in the RS232 (default) position if the TIC is to be

used to configure the pump. Refer to

Connect the serial interface to the customer control

equipment on page 41

The TIC is supplied with a Windows

based PC program which allows the pump to be

configured from a single PC. The program has a simple user interface and it is not

necessary to use the ASCII message protocol given in

Connection for serial control and

monitoring on page 41

. The TIC PC program can save number of pump configurations

which can be downloaded to the other pumps.

Page 16

B85200880_D - Introduction

Содержание nEXT200200





































































































Результаты поиска

Содержание nEXT200200

Отзывы:

Бренды по названию

Популярные бренды

Edwards nEXT200200, Инструкция по эксплуатации

Результаты поиска

Содержание nEXT200200

Отзывы:

Бренды по названию

Популярные бренды