Edwards nEXT 55 Скачать руководство пользователя страница 41

Страница: 41 / 116

4.2 Connect to the vacuum system

WARNING: INSTALLATION SEQUENCE

Risk of injury. Install the pump in the vacuum system before you connect the motor

controller to the power supply so the pump cannot operate.

WARNING: TRIP HAZARD

Risk of injury and damage to equipment. Make sure that the cable and pipe work

attached to the pump are carefully routed. Failure to do so can cause a slip or trip

hazard and damage to the cable.

4.2.1 Remove and replace the inlet screen

The inlet screen is installed on the CF pumps only. Remove the inlet screen only if the

debris cannot fall into the pump. If the inlet screen is removed, the pumping speed will

increase by a maximum of 20%.

WARNING: SHARP OBJECT

Risk of injury. The rotor blades on the pump are sharp. Removal of inlet screens or

strainers exposes the sharp edges or moving parts that can cause injury.

WARNING: FOREIGN OBJECTS INSIDE THE PUMP

Risk of damage to equipment. Make sure that there are no foreign objects inside the

pump when you do the installation. Install the supplied integral mesh centring O-ring

seal or the mesh screen when you install the pump.

WARNING: DEBRIS IN THE PUMP

Risk of damage to equipment. If the pump fractures and the inlet screen cannot trap

all the debris, make sure that the system can contain the debris that escapes from the

pump.

WARNING: INLET SCREEN

Risk of damage to equipment. The inlet screen is a coarse filter for debris and

prevents contamination of the pump. Do not use the inlet screen as a finger guard or

remove it until you are ready to mount the pump onto the system.

To remove the inlet screen from a pump with CF inlet flange, use a bent wire hook

or a small screwdriver. Be careful when you remove the inlet screen out from the

inlet flange.

To replace an inlet screen, put it centrally over the CF inlet flange.

Apply equal pressure with the fingers around the edge of the screen and push the

inlet screen down.

07/2021 - ©Edwards Limited

Page 41

B8G000880_E

B8G000880_E - Installation

Содержание nEXT 55





















































































































Результаты поиска

Содержание nEXT 55

Отзывы:

Похожие инструкции для nEXT 55

Бренды по названию

Популярные бренды

Edwards nEXT 55, Инструкция по эксплуатации

Результаты поиска

Содержание nEXT 55

Отзывы:

Похожие инструкции для nEXT 55

Бренды по названию

Популярные бренды