Edwards nEXT 55 Скачать руководство пользователя страница 29

Страница: 29 / 116

Figure 12 Interface circuits for nEXT turbo pump controllers

3.10 Motor controller auxiliary connector socket

The pump has a 4-way auxiliary connector socket at the side of the motor controller.
The mating plug for the connector is pre-installed to a number of accessories or

available as an accessory. Refer to

Accessories

on page 105.

The connector supplies the power to the vent valve or a fan. The connector is shown in

Figure: Valve connector

, with the polarity of the pins marked, when the vent valve or fan

is set to on.
The auxiliary connector output is controlled to 24 V d.c. to control the accessories, even

when the pump is in operation from a 48 V d.c. supply and is protected from the

overload and short circuits. If the auxiliary load current becomes more than the value

07/2021 - ©Edwards Limited

Page 29

B8G000880_E

B8G000880_E - Technical data

Содержание nEXT 55





















































































































Результаты поиска

Содержание nEXT 55

Отзывы:

Бренды по названию

Популярные бренды

Edwards nEXT 55, Инструкция по эксплуатации

Результаты поиска

Содержание nEXT 55

Отзывы:

Бренды по названию

Популярные бренды