manualshive.com logo in svg

Edwards EXC120, Инструкция по эксплуатации

Поделиться
Скачать
Edwards EXC120 Скачать руководство пользователя страница 20

D396-14-880 Issue J

Page 12

© Edwards Limited 2008. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Introduction

1.9.3

Axial Emergency (EXC300M only)

The EXT250M pump has sensors which detect the axial displacement of the pump rotor; the outputs of these sensors 
are monitored by the Controller.

The Controller trips into Axial Emergency condition if:

z

The displacement of the rotor exceeds set limits for more than 2 seconds.

z

The displacement of the rotor repeatedly exceeds set limits (due to oscillation).

When the Controller trips into Axial Emergency condition, the electrical supply to the pump-motor is switched off, 
the Emergency LED on the front panel goes on and the Axial Emergency status output signal on the logic interface 
opens. The EXT250M pump electromagnetic bearings remain active, although the rotor assembly may contact the 
safety bearings if the axial loading exceeds the capabilities of the bearing drive.

1.10

Electrical connections

All electrical connections to the Controller are on the rear panel: see Figures 

3

 to 

5

.

Содержание EXC120























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды