background image

© Edwards Limited 2015. All rights reserved. 

Page 29

Edwards and the Edwards logo are trademarks of Edwards Limited.

Service and accessories

D396-20-880 Issue H

7

Service and accessories

7.1

Introduction

Edwards products, spares and accessories are available from Edwards companies in Belgium, Brazil, China, France, 
Germany, Israel, Italy, Japan, Korea, Singapore, United Kingdom, U.S.A and a world-wide network of distributors. 
The majority of these centres employ Service Engineers who have undergone comprehensive Edwards training 
courses.

Order spare parts and accessories from your nearest Edwards company or distributor. When you order, state for each 
part required:

Model and Item Number of your equipment

Serial number

Item Number and description of part.

7.2

Service

Edwards products are supported by a world-wide network of Edwards Service Centres. Each Service Centre offers a 
wide range of options including: equipment decontamination; service exchange; repair; rebuild and testing to factory 
specifications. Equipment which has been serviced, repaired or rebuilt is returned with a full warranty.

Your local Service Centre can also provide Edwards engineers to support on-site maintenance, service or repair of 
your equipment.

For more information about service options, contact your nearest Service Centre or other Edwards company.

7.3

Accessories

7.3.1

Electrical supply cable

You must use a suitable electrical supply cable to connect the Controller to your electrical supply. An electrical 
supply cable is not supplied with the Controller.

Cable

Item Number

Electrical supply cable (2 m length, unterminated)

D385-01-102

Содержание EXC 100E











































Отзывы: