manualshive.com logo in svg

Edwards A705-41-000, Инструкция по эксплуатации

Поделиться
Скачать
Edwards A705-41-000 Скачать руководство пользователя страница 13

© Edwards Limited 2011. All rights reserved. 

Page 7

Edwards and the Edwards logo are trademarks of Edwards Limited.

Introduction

A705-40-880 Issue B

1.8

Pump motor applicability

The Pumping System instruction manual you receive will specify the type of motor fitted to your EDP pump.

Note that you will also receive the appropriate Motor instruction manual for your pump.

The pumps are designed to operate with motors rated as specified in 

Section 2.4

, with the maximum outlet pressures 

listed in the pump descriptions on the front cover of this manual. 

Note that the EDP250 can be configured with two different ratings of motor, one for each of the two different 
maximum outlet pressures with which the pump is designed to operate.

1.9

Hazardous area and safe area versions of the pump

The EDP pumps are available in versions suitable for Hazardous Area or Safe Area operation.

Refer to your EDP Pumping System instruction manual, which will specify the technical specification of your system. 
The EDP Pumping System instruction manual will define whether your system is suitable for Safe Area operation only, 
or will define the Hazardous Area classification in which your system is certified to operate.

1.10

Accessories

A number of accessories are available for the EDP pumps; use these to configure the pump for specific applications. 
These accessories are listed in 

Section 7.4

.

1.11

Ordering options

The basic EDP80 and EDP160 pumps are supplied with a drive coupling (see 

Section 1.6.2

) If required, you can order 

these pumps to be supplied with a torque limiter fitted; refer to 

Section 1.6.3

 for a description of the torque limiter 

operation.

1.12

Normal/abnormal operation

1.12.1

Normal operation

Normal operation is defined by this instruction manual. In normal operation, the EDP pump is safe to handle gases 
from gas groups IIA, IIB and IIC if no flame arresters are fitted. If flame arresters are fitted the designation of the 
flame arresters will determine the gas group that can be pumped with the pumping system. Please also read the 
exceptions listed in 

Section 1.12.2

.

If the EDP pump is to be used in a non-ATEX system:

We recommend that you fit approved flame arrestors to the EDP pump, if you intend to pump potentially 
explosive atmospheres. 

If the EDP pump is to be used as part of an ATEX system:

The use of approved flame arrestors is mandatory for some ATEX system classifications. Refer to the ATEX 
System instruction manual for more information.

Содержание A705-41-000



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды