Edic Saturn 17DS3-BK-SV Скачать руководство пользователя страница 7

Страница: 7 / 13

3. Insert the locking clamp handle/spade bolt assembly

through the Cord Hook Clamp assembly (located on the

handle) and the left and right handle braces ( D11481,

D11482).

4. Put the locking clamp handle in the unlocked position

(pointing up) and start tightening the nut C11558 on the

threaded portion of the spade bolt (C11536).

5. Check the cord hook clamp is sliding up

and down freely on the handle stem with lock-

ing clamp handle in the unlocked position.

6. Place the handle in the down position to check the

locking function. If too tight, unlock the handle and

loosen the nut (C11558) slightly. If too loose, unlock the

the handle and tighten the nut (C11558), as needed. You

have assembled the cord hook clamp assembly properly

when the locking handle locks firmly in the DOWN po-

sition and unlocks and slides easily in the UP position.

(UNLOCKED)

(LOCKED)

7. Plug the male motor cord plug to the female handle

cord plug. Your Assembly is done. Refer to Brush/Pad

driver installation and operation sections before operat-

ing the unit.

Содержание Saturn 17DS3-BK-SV













