Edgetech USBL BROADBAND ACOUSTIC TRACKING SYSTEM Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 102

Edgetech USBL BROADBAND ACOUSTIC TRACKING SYSTEM Скачать руководство пользователя страница 7

vii

WARRANTY STATEMENT

All equipment manufactured by EdgeTech is warranted against defective components and workmanship
for a period of one year after shipment. Warranty repair will be done by EdgeTech free of charge.
Shipping costs are to be borne by the customer. Malfunction due to improper use is not covered in the
warranty, and EdgeTech disclaims any liability for consequential damage resulting from defects in the
performance of the equipment. No product is warranted as being fit for a particular purpose, and there is
no warranty of merchantability. This warranty applies only if:

i.

The items are used solely under the operating conditions and in the manner recommended in
Seller's instruction manual, specifications, or other literature.

ii.

The items have not been misused or abused in any manner, nor have repairs been attempted
thereon without the approval of EdgeTech Customer Service.

iii.

Written notice of the failure within the warranty period is forwarded to Seller and the directions
received for properly identifying items returned under warranty are followed.

iv.

The return notice authorizes Seller to examine and disassemble returned products to the extent
Seller deems necessary to ascertain the cause for failure.

The warranties expressed herein are exclusive. There are no other warranties, either expressed or implied,
beyond those set forth herein, and Seller does not assume any other obligation or liability in connection
with the sale or use of said products. Any product or service repaired under this warranty shall be
warranted for the remaining portion of the original warranty period only.
Equipment not manufactured by EdgeTech is supported only to the extent of the original manufacturer's
warranties.

«
...
5
6
7
8
9
...
»

Содержание USBL BROADBAND ACOUSTIC TRACKING SYSTEM







































































































Отзывы:

Нет отзывов