Edgetech 6205S2 Скачать руководство пользователя страница 39

Страница: 39 / 108

3-39

3.0

TECHNICAL DESCRIPTION

The complete 6205s2 system consists of a sonar head, a topside interface box, and an attached topside

computer. This section describes the 6205s2 System's main components and provides drawings for system

integration and operations.

3.1

The 6205s2 Sonar Head

The 6205s2 is a lightweight, durable, hydrodynamic sonar head designed for side scan and bathymetric

surveys. The sonar electronics are contained inside a single housing, and two dual side scan and

bathymetric arrays are mounted on the port and starboard sides of the vehicle. A sound velocity sensor

is housed in the nose cone. A deck cable connector and optional GNSS/INS cable connector are located

on the top aft section of the sonar head.

Figure 3-1: 6205s2 Sonar Head Port View

Figure 3-2: 6205s2 Aft View

Figure 3-3: 6205S2

Forward View

Figure 3-4: 6205s2 Nose Cap

Removed- AML SVT OEM Probe

Visible and Optional Adaptor

Flange Installed

Nosecone Housing Sound

Velocity Sensor

Mounting Plate

Deck Cable

Connector

[2] Dual-Fre Bathymetric Sonar Arrays (Port and Starboard Sides)

GNSS/INS Cable

Connector

Housing

Содержание 6205S2













































































































Результаты поиска

Содержание 6205S2

Отзывы:

Похожие инструкции для 6205S2

Бренды по названию

Популярные бренды

Edgetech 6205S2, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S2

Отзывы:

Похожие инструкции для 6205S2

Бренды по названию

Популярные бренды