Edgetech 6205S Скачать руководство пользователя

Страница: 88 / 97

8-71

CAUTION!

EdgeTech recommended performing the process described in the section

below through Discover, but the process below provides an alternative.

Please refer to the

ISCOVER

ATHYMETRY

ANUAL

for information on how

to complete this process in Discover.

8.3.5

Applanix POSMV Configuration

The 6205s is compatible with the POSMV system from Applanix. Follow the below steps to configure the

6205s and the POSMV for communication over the Ethernet interface via UDP.
Utilizing the Applanix POSVIEW software:

Set the ethernet real-time output data to groups 3,7,10, and 102. The output rate of the POSMV

data should be set to 50Hz.

The POSMV must also be set to Falling (Negative) Edge or

Active Low

for the 1PPS as the 6205s

defaults to sync on the falling edge.

Set the POSMV Time Tag 1 to UTC.

To configure the 6205s COM ports for the UDP messages from the POSMV:

Follow steps in

UDP

ONNECTIONS

Under [Serial1], [Serial2], and [Serial3] set Create = 0.

Under [Serial5], set Create = 1 and remove the semicolon from the beginning of each line in the
[Serial5] section.

Ensure the command Parserparameters=HEAVESCALE -1.0 is present in the [Serial5] section. If it
is not present, add it.

Содержание 6205S


































































































Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды

Edgetech 6205S, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды