Edgetech 6205S Скачать руководство пользователя страница 55

Страница: 55 / 97

5-38

6205s BATHYMETRIC AND SIDE SCAN SONAR

0020300_REV_E

5.4

Field Exchangeable Frequency Operations

The Field Swappable functionality is only possible with 230 / 550 kHz Side Scan systems.
In order to switch between different bathymetry frequencies, the 6205s arrays must be exchanged with

the corresponding bathymetry array. For instance, if the Sonar Head is configured as a 230 kHz/550 kHz

Side Scan with 230 kHz bathymetry and the user wants to exchange the bathymetry frequency to the 550

kHz channel, then the following procedure should be followed.

Tools

•

1/16-inch Allen Wrench

•

3/16-inch Allen Wrench

•

Tube of Thread Lock

Place the 6205s on a stable and level platform, such as a workbench or boat deck.

Figure 5-4: Unit on Stable Platform

Removing the [8] cap screws using a

” Allen key on the right and left sides of the housing.

Содержание 6205S


































































































Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды

Edgetech 6205S, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды