Edgetech 6205S Скачать руководство пользователя страница 21

Страница: 21 / 97

2-4

6205s BATHYMETRIC AND SIDE SCAN SONAR

0020300_REV_E

SYSTEM DESCRIPTION

The complete 6205s system consists of a swath bathymetry and side scan sonar head, and a topside

interface box. This section describes the 6205s System's main components and lists its specifications.

2.1

The 6205s Sonar Head

The 6205s Swath Bathymetry and Side Scan Sonar Head is available in a variety of frequency options:

•

230 / 550 kHz Dual Frequency Side Scan with 230 kHz Bathymetry Data

•

230 / 550 kHz Dual Frequency Side Scan with 550 kHz Bathymetry Data

•

550 / 850 kHz Dual Frequency Side Scan with 550 kHz Bathymetry Data

•

550 / 1600 kHz Dual Frequency Side Scan with 550 kHz Bathymetry Data

The frequency sets listed above were chosen to provide optimum results for any given water depth up to

200m (660ft) below the transducer. The 6205s is for water depths between 5m – 50m (15ft – 164ft).

Optimal frequency depends on survey requirements.
EdgeTech has designed the 230 kHz/550 kHz model 6205s Sonar Head with Field Exchangeable Arrays to

mitigate frequency tradeoffs. The bathymetry frequency can be switched from the low-frequency channel

to the high-frequency channel or vice versa.
The 6205s Swath Bathymetry and Side Scan Sonar Head comes standard with a sonar processor, port and

starboard sonar arrays, a sound velocity sensor (SVS), and housing. These components are demonstrated

IGURE

2-1

Содержание 6205S


































































































Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды

Edgetech 6205S, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды