manualshive.com logo in svg

Edge-Core ES3510MA-DC, Руководство по управлению, Страница: 908 / 1098

Поделиться
Скачать
Edge-Core ES3510MA-DC Скачать руководство пользователя страница 908

C

HAPTER

 38

  |  Multicast Filtering Commands

IGMP Snooping

–  908  –

C

OMMAND

 U

SAGE

 

◆

When a multicast host leaves a group, it sends an IGMP leave message. 

When the leave message is received by the switch, it checks to see if 

this host is the last to leave the group by sending out an IGMP group-

specific or group-and-source-specific query message, and starts a 

timer. If no reports are received before the timer expires, the group 

record is deleted, and a report is sent to the upstream multicast router.

◆

A reduced value will result in reduced time to detect the loss of the last 

member of a group or source, but may generate more bursty traffic. 

◆

This command will take effect only if IGMP snooping proxy reporting is 

enabled (

page 898

).

E

XAMPLE

 

Console(config)#ip igmp snooping vlan 1 last-memb-query-intvl 700

Console(config)#

ip igmp snooping

vlan mrd

This command enables sending of multicast router solicitation messages. 

Use the 

no

 form to disable these messages.

S

YNTAX

 

[

no

] 

ip igmp snooping vlan

 

vlan-id

 

mrd

vlan-id

 - VLAN ID (Range: 1-4093) 

D

EFAULT

 S

ETTING

 

Enabled 

C

OMMAND

 M

ODE

 

Global Configuration

C

OMMAND

 U

SAGE

 

◆

Multicast Router Discovery (MRD) uses multicast router advertisement, 

multicast router solicitation, and multicast router termination messages 

to discover multicast routers. Devices send solicitation messages in 

order to solicit advertisement messages from multicast routers. These 

messages are used to discover multicast routers on a directly attached 

link. Solicitation messages are also sent whenever a multicast 

forwarding interface is initialized or re-initialized. Upon receiving a 

solicitation on an interface with IP multicast forwarding and MRD 

enabled, a router will respond with an advertisement.

◆

Advertisements are sent by routers to advertise that IP multicast 

forwarding is enabled. These messages are sent unsolicited periodically 

on all router interfaces on which multicast forwarding is enabled. They 

are sent upon the expiration of a periodic timer, as a part of a router's 

start up procedure, during the restart of a multicast forwarding 

interface, and on receipt of a solicitation message. When the multicast 

services provided to a VLAN is relatively stable, the use of solicitation 

Содержание ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов