manualshive.com logo in svg

Edge-Core ES3510MA-DC, Руководство по управлению, Страница: 727 / 1098

Поделиться
Скачать
Edge-Core ES3510MA-DC Скачать руководство пользователя страница 727

C

HAPTER

 27

  |  Interface Commands

–  727  –

the speed/duplex mode under auto-negotiation, the required mode 

must be specified in the capabilities list for an interface.

E

XAMPLE

 

The following example configures port 5 to 100 Mbps, half-duplex 

operation.

Console(config)#interface ethernet 1/5

Console(config-if)#speed-duplex 100half

Console(config-if)#no negotiation

Console(config-if)#

R

ELATED

 C

OMMANDS

 

negotiation (725)

capabilities (721)

switchport packet-

rate

This command configures broadcast, multicast and unknown unicast storm 

control. Use the 

no

 form to restore the default setting.

S

YNTAX

 

switchport 

{

broadcast

 | 

multicast

 | 

unicast

} 

packet-rate

 

rate

no switchport 

{

broadcast

 | 

multicast

 | 

unicast

}

broadcast

 - Specifies storm control for broadcast traffic.

multicast

 - Specifies storm control for multicast traffic.

unicast

 - Specifies storm control for unknown unicast traffic.

rate

 - Threshold level as a rate; i.e., kilobits per second. 

(Range: 64-100000 Kbps for Fast Ethernet ports, 

             64-1000000 Kbps for Gigabit Ethernet ports)

D

EFAULT

 S

ETTING

 

Broadcast Storm Control: Enabled, packet-rate limit: 64 kbps 

Multicast Storm Control: Disabled 

Unknown Unicast Storm Control: Disabled 

C

OMMAND

 M

ODE

 

Interface Configuration (Ethernet)

C

OMMAND

 U

SAGE

 

◆

When traffic exceeds the threshold specified for broadcast and 

multicast or unknown unicast traffic, packets exceeding the threshold 

are dropped until the rate falls back down beneath the threshold. 

◆

Traffic storms can be controlled at the hardware level using this 

command or at the software level using the 

auto-traffic-control

 

command. However, only one of these control types can be applied to a 

port. Enabling hardware-level storm control on a port will disable 

automatic storm control on that port.

Содержание ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов