manualshive.com logo in svg

Edge-Core ECS3510-28F, Руководство по установке, Страница: 63 / 72

Поделиться
Скачать
Edge-Core ECS3510-28F Скачать руководство пользователя страница 63

–  63  –

G

LOSSARY

10BASE-T

IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 
5 UTP cable.

100BASE-TX

IEEE 802.3u specification for 100 Mbps Ethernet over two pairs of Category 5 
UTP cable.

1000BASE-LH

Specification for long-haul Gigabit Ethernet over two strands of 9/125 micron 
core fiber cable.

1000BASE-LX

IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/125, 62.5/
125 or 9/125 micron core fiber cable.

1000BASE-SX

IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/125 or 
62.5/125 micron core fiber cable.

1000BASE-T

IEEE 802.3ab specification for Gigabit Ethernet over 100-ohm Category 5, 5e or 
6 twisted-pair cable (using all four wire pairs).

A

UTO

-N

EGOTIATION

Signalling method allowing each node to select its optimum operational mode 
(e.g., speed and duplex mode) based on the capabilities of the node to which it 
is connected.

Содержание ECS3510-28F









































































Отзывы:

Нет отзывов