EDER Maschinenbau Titan 80 Pro Скачать руководство пользователя | Manualshive

Страница: 22 / 28

background image

270900_00 | 02.2022

Titan 80 Pro 22

EN

Felling the tree

>

Make sure that there are no other people or objects in the felling
area.

>

Give warning signs such as "Attention! Tree falling!"

>

Operate the ratchet or impact wrench clockwise so that the lifting
wedge made of special plastic pushes forward and gradually
causes the tree to fall.

>

Keep pushing the safety wedge until the tree falls.

>

Move out of the danger zone quickly.

>

Keep an eye on the crown and nearby trees.

>

Stay in a safe area until the tree is on the ground and there are no
more dangers.

>

If the full extension length has been reached but the tree has not
yet fallen, you must reposition the Titan 80 Pro. To do this, follow
the steps below:

>

The tree must be secured by sufficiently high safety wedges.

>

Operate the ratchet or impact wrench anti-clockwise to retract the
lifting wedge.

>

Reposition the Titan 80 Pro and repeat the lifting process by turning
the ratchet or impact wrench clockwise.

ATTENTION

Risk of damage to the Titan 80 Pro

The shaft drive is mechanically limited. When the full extension
length of the lifting wedge is reached, do not turn the ratchet or
impact wrench any further clockwise.

>

Never turn the ratchet with force and never extend it.

>

Do not use an impact wrench with more than 1300 Nm.

«
...
20
21
22
23
24
...
»

Содержание Titan 80 Pro





























Отзывы:

Нет отзывов

Похожие инструкции для Titan 80 Pro

Бренд: FAR Страницы: 11

Бренд: FAR Страницы: 44

Бренд: FAR Страницы: 28

Бренд: FAR Страницы: 32

Бренд: FAR Страницы: 24

Бренд: FAR Страницы: 68

Бренд: FAR Страницы: 8

Бренд: FAR Страницы: 15

Бренд: Xaoc Devices Страницы: 8

Бренд: Paslode Страницы: 20

Бренд: Worx Nitro Страницы: 10

Бренд: NSI Solutions Страницы: 10

Бренд: Performance Tool Страницы: 6

Бренд: Wel-Bilt Страницы: 7

Бренд: XPOtool Страницы: 12

METERPULLER M-001

Бренд: Rauckman Utility Products Страницы: 8

Бренд: On-Q Страницы: 2

Бренд: Glendo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды