Part #2201, 2204, 2205, 2207, 2208, 2209 & 2210
Rev. 7/09 - AJ/mc
©2009 Edelbrock Corporation
Brochure #63-0154
Page 1 of 4
PERFORMER-PLUS AND PERFORMER RPM
HYDRAULIC ROLLER CAMSHAFTS
For 283-400 C.I.D. Chevrolet V8 Engines
PART #2201, 2204, 2205, 2207, 2208, 2209 & 2210
INSTALLATION INSTRUCTIONS
®
PLEASE
study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,
it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our
Technical Hotline at:
1-800-416-8628
, 7:00 am - 5:00 pm, Pacific Standard Time.
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation
will void your warranty and may result in poor performance and engine or vehicle damage.
These instructions are designed to give general installation guidelines.
A complete step-by-step procedure manual would require many
pages. If you are a novice or just learning to work on automotive engines, we recommend consulting either Chilton or Motors automotive manuals
before you begin. You may also contact an experienced mechanic. Please be advised that an improper installation may result in
LOW MILEAGE, POOR
PERFORMANCE, COSTLY REINSTALLATION AND EVEN ENGINE DAMAGE.
Installing a camshaft is a complex procedure. Please follow these
instructions carefully. Failure to do so may void your warranty. Refer to Edelbrock catalog for each camshaft’s specific application coverage.
•
Before you begin the removal and installation process, please examine the kit for possible shipping damage. If the camshaft is damaged, contact
your dealer immediately. Also, make sure you have all the recommended tools and parts as listed below. As you read through these instructions
the first time, use the preparation checklist to check off the exact items you will need.
•
Performer-Plus and Performer RPM camshafts are ground specifically for use with the corresponding Performer or Performer RPM manifold. They
are dyno-matched and street proven to work as a team; especially when part of an Edelbrock Total Power Package. However, Performer-Plus or
Performer RPM camshaft package may also be used with other components designed to operate in a similar RPM range.
PREPARATION CHECKLIST
Tools & Equipment For Installation
❑
Box and open end wrenches
❑
Socket set
❑
Distributor wrench
❑
Pliers (channel locks & hose clamp)
❑
Screw drivers (regular and phillips)
❑
Torque wrench
❑
Hammer
❑
Gasket scraper or putty knife
❑
Timing light vacuum gauge
❑
Rags
❑
Water bucket
❑
Harmonic balancer puller
❑
Masking tape (for tagging hoses and electrical wires)
❑
Chalk , paper and pencil
❑
Crankshaft dampener puller
Hardware & Parts To Buy
❑
Edelbrock Roller Lifters or equivalent:
Pre-1986 - Edelbrock #97383
1987-Later - OEM or Edelbrock #97384
❑
Edelbrock Hardened Push Rods or equivalent:
All Years - Edelbrock #9653
❑
Camshaft thrust button (pre-1986 only) - supplied
❑
Edelbrock Intake Manifold Gaskets or equivalent:
Pre-1986 heads - Edelbrock #7201
E-Tec/Vortec heads - Edelbrock #7235
❑
Edelbrock True Rolling Timing Chain Set #7800, 7801,
7880, 7331, or 7332 (See Catalog for correct application)
❑
Pipe plugs, if needed
❑
Edelbrock Gasgacinch #9300
❑
RTV Silicone sealer
❑
Engine oil and filter
❑
Radiator coolant
❑
Front cover oil seal, OEM or equivalent
❑
Valve Springs with a closed pressure of 110-120, open
pressure of 330-340 and a lift of .550”
(.600” for #2207)
NOTE: Edelbrock Sure Seat Valve Springs #5703 are
recommended for use with Performer camshafts
#2208 & #2209 ONLY.
