EDAN F15 Series Скачать руководство пользователя страница 44

Страница: 44 / 80

F15 Series Fetal & Maternal Monitor Service Manual

Troubleshooting

- 33 -

LCD

displays

improper

characters.

LCD defective.

Replace the LCD.

7.3 Touch Screen Failures

Phenomenon

Possible Cause

Solution

The touch screen is not
functioning.

The touch screen related
cable(s)

(are)

disconnected.

Check  that  the  touch  screen  related
cables  between  the  main  control
board, touch screen controlling board
and  the  touch  screen  are  well
connected.

The

touch

screen

damaged.

Replace the touch screen.

The touch position invalid.

The touch screen is not
calibrated.

Calibrate the touch screen using
procedures described in section

4.6

Calibrating Touch Screen

7.4 Sound Failures

Phenomenon

Possible Cause

Solution

Hoarse or odd sound from
loudspeaker.

Loudspeaker defective.

Replace the loudspeaker.

Main

control

board

defective.

Replace the main control board.

7.5 Recorder Failures

Phenomenon

Possible Cause

Solution

No paper advances.

No paper in the drawer.

Load paper and close the drawer.

Paper drawer is open.

Close the drawer.

Paper jam.

Open the drawer and remove the
paper jam. Re-load paper then close
the drawer.

controlling

board

defective.

Replace the print controlling board.

Recorder connection failure.

Check all the connectors.

Gear assembly defective.

Replace the gear assembly.

Main

control

board

defective.

Replace the main control board.

The  “Check  paper”  alarm
message  appeared  on  the
screen,  but  the  drawer  is  not
empty.

Paper sensor dirty.

Clean the paper sensor with a dry
clean cloth.

Paper sensor defective.

Replace the paper sensor.

Содержание F15 Series

















































































Результаты поиска

Содержание F15 Series

Отзывы:

Бренды по названию

Популярные бренды

EDAN F15 Series, Руководство по обслуживанию

Результаты поиска

Содержание F15 Series

Отзывы:

Бренды по названию

Популярные бренды