manualshive.com logo in svg

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
ECR International Utica Boilers UCS-380 Скачать руководство пользователя страница 75

75

13 - TROUBLE SHOOTING

Troubleshooting Chart 1

E02 

- Supply Sensor Short

E03

 - Supply Sensor Open

E04

 - Heat Exchanger Temp.

E05

 - Heat Exchanger Temp.

E06

 - Return Sensor Short

E07

 - Return Sensor Open

E08

 - Low Return Temp. 

E09

 -High Return Temp.  

Locate Appropriate Sensor

See Figure 1 (page) and 

Figure (Wire Diagram)

Trace wire leads.  Are all 

connections tight and wires 

undamaged? 

NO

YES

Check continuity across 

sensor.

OK?

NO

YES

Repair wire 

and/or fix 

connection.

Check sensor element is 

properly installed in pipe.

NO

YES

Replace 

Sensor

Replace 

Control Board

Re-Install

Sensor Properly

Check sensor resistance 

and compare to 

temperature resistance 

curve (Figure 13-1 page 

87. (Remove sensor if 

needed). OK?

NO

YES

Replace 

Sensor

Note

DOMESTIC HOT WATER SENSOR:

  If the DHW sensor is shorted it will act as a closed thermostat and boiler will 

continuously fire.

 PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды