ECR International Utica Boilers UCS-380 Скачать руководство пользователя | Manualshive

Страница: 40 / 88

background image

40

8.1

General

Electrically bond boiler to ground in accordance with

requirements of authority having jurisdiction. Refer to:

•

USA- National Electrical Code, ANSI/NFPA 70.

• Canada - Canadian Electrical Code, Part I, CSA C22.1:

Safety Standard for Electrical Installations.

8.2

Electric Knockouts

(Figure 8-1)

• Eight knockouts located on bottom of chassis.

A.  Thermostat (Section 8-10)
B.  Outdoor Reset (Section 8-9)
C.  Frost Protections ( Section 8-12)
D.  DHW Sensor (Sections 8-11, 8-13)
E.  Release Input (

Section

8-7)

F.  Shutdown Input (Section 8-15)
G.  Analog Input (Section 8-8, IF-01 board)
H.  Analog Output (Section 8-8, IF-01 board)
I.  Alarm (IF02 or SCU-SO2 board)
J.  External Heat System Pump (Section 8-8, SCU-S02

board)

K. DHW Diverter/Pump (Section 8-8)
L.

External Gas Shutoff (Section 8-8)

M. Minimum Gas Pressure Switch (Section 8-8)

N.

Solar Input (Section 8-8)

WARNING

Electrical shock hazard. Turn OFF electrical power

supply at service panel before making electrical

connections. Failure to do so could result in death

or serious injury.

!

FIGURE

8-1

Electric Knockouts Bottom Of Boiler

8 Wire

Knockouts

Back of Boiler

8 - ELECTRICAL CONNECTIONS

8.3 Electrical Connections

• Boiler requires 120V 60Hz power supply. Verify electrical

supply is polarized.

• Boiler shall be grounded and on dedicated circuit.
• Shall be one common isolator, providing electrical isolation

for boiler and any external controls. Using PVC insulated

cable 18 AWGx3C 221°F / 105 °C.

• All wiring must be installed in accordance with

requirements of the National Electrical Code and any

additional national, state, or local code requirements

having jurisdiction. All wiring must be N.E.C. Class 1.

• Canada, installation must conform to CSA C22.1 Canadian

Electrical Code Part 1 and any local codes.

• If replacing original boiler wiring use only TEW 105°C or

equivalent.

• 12 Amp Maximum rating.

PN 240011662 Rev. H [04/30/2019]

«
...
38
39
40
41
42
...
»

Содержание Utica Boilers UCS-380

























































































Отзывы:

Нет отзывов

Похожие инструкции для Utica Boilers UCS-380

Бренд: Kardia Страницы: 43

Eclipse 216 ESS

Бренд: VOKERA Страницы: 40

Flue pipe VKK SERIES

Бренд: Vaillant Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: U.S. Boiler Company Страницы: 8

Бренд: Buderus Страницы: 36

Бренд: Weil-McLain Страницы: 12

Бренд: Kalvis Страницы: 12

GREENSTAR UTILITY

Бренд: Worcester Страницы: 64

Condexa Pro 100 P

Бренд: Riello Страницы: 23

Бренд: Olsen Страницы: 84

Бренд: Gorenje Страницы: 24

Xilo D 20 MC W TOP U/IT

Бренд: LAMBORGHINI Страницы: 32

Бренд: Ariston Страницы: 16

Бренд: Teba therm Страницы: 21

Бренд: Marco Страницы: 1

Бренд: Baxi Страницы: 16

PREMIER PLUS 400

Бренд: Baxi Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды