ECR International Dunkirk DCB-100 Скачать руководство пользователя страница 47

Страница: 47 / 143

8.1

General

Electrically bond boiler to ground in accordance with

requirements of authority having jurisdiction. Refer to:

• USA- National Electrical Code, ANSI/NFPA 70.

• Canada - Canadian Electrical Code, Part I, CSA C22.1:

Safety Standard for Electrical Installations.

• Install all wiring in accordance with requirements of

National Electrical Code and any additional national, state,

or local code requirements having jurisdiction.

• In Canada, installation must conform to CSA C22.1

Canadian Electrical Code Part 1 and any local codes.

• All wiring shall be N.E.C. Class 1.

• Boiler shall be electrically grounded in accordance with the

National Electrical Code, ANSI/NFPA No. 70-latest edition.

• Boiler requires a 120V 60Hz power supply. Ensure electrical

supply is polarized.

• There shall only be one common isolator, providing

complete electrical isolation, for boiler and any external

controls. Using PVC insulated cable 12 AWGx3C 221°F

(105 ºC).

WARNING

Electrical shock hazard. Turn OFF electrical power

supply at service panel before making electrical

connections. Failure to do so could result in death or

serious injury.

FIGURE 8-1 Electric Knockouts Bottom Of Boiler -

Illustration shown (size 205), illustration is for location

purposes, wiring knockouts found same general location on all

sizes.

8 - ELECTRICAL CONNECTIONS

Note

Wiring diagrams can be found in Appendix A of
this Manual.

8.2 Electrical Connections

• Boiler requires 120V 60Hz power supply. Verify electrical

supply is polarized.

• Boiler shall be grounded and on dedicated circuit.

• Shall be one common isolator, providing electrical isolation

for boiler and any external controls. Using PVC insulated

cable 18 AWGx3C 221°F (105°C). (Ground boiler with non

spliced wire.)

• All wiring must be installed in accordance with

requirements of the National Electrical Code and any

additional national, state, or local code requirements

having jurisdiction. All wiring must be N.E.C. Class 1.

• Canada, installation must conform to CSA C22.1 Canadian

Electrical Code Part 1 and any local codes.

• If replacing original boiler wiring use only TEW 105°C or

equivalent.

•

If appliance is connected to in floor system, install limit

thermostat to prevent latter from overheating.

Model

Size

75 &

100

115

125

150

165

205

Power Supply

120V - 60Hz

Power

Consumption 118 W 125 W 133 W 142 W 173 W

182 W

Internal Fuse

(Qty. 2)

F3.15 A

Electrode

Spark Gap

1/8" to 3/16" [3.1 mm to 4.7 mm]

Electric

Knockouts

DANGER

Electrocution Hazard! HIGH VOLTAGE - Connections

in terminal block M1 are high voltage (120V / 60Hz).

Before making connections, verify appliance is

disconnected from power supply. Respect the input

polarity on terminal block M1: L (LINE) - N (NEUTRAL).

Failure to follow these instructions WILL result in death

or serious injury.

240013501 REV A [03/15/2022]

Содержание Dunkirk DCB-100
















































































































































Результаты поиска

Содержание Dunkirk DCB-100

Отзывы:

Бренды по названию

Популярные бренды

ECR International Dunkirk DCB-100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk DCB-100

Отзывы:

Бренды по названию

Популярные бренды