ECR International Dunkirk DCB-100 Скачать руководство пользователя страница 23

Страница: 23 / 143

5.4 Approved Venting Materials

5 - COMBUSTION AIR AND VENT PIPING

5.5 Vent Termination

•

Terminate combustion air and vent pipes with fittings or

coaxial vent kit. Refer to venting illustrations for details.

• Separate vent terminal from air inlet terminal to prevent

flue gas recirculation. If T-Terminal is used on flue pipe

at sidewall, air inlet terminal shall be at least 36" or more

away from vent terminal.

• Locate combustion air termination as far as possible from

swimming pool, swimming pool pump house, and other

sources of airborne chlorine.

• Locate combustion air and vent terminals as required by

authority having jurisdiction.

Installation shall conform to requirements of authority having
jurisdiction or in absence of such requirements:

• USA - National Fuel Gas Code, ANSI Z223.1/NFPA 54.
• Canada - Natural Gas and Propane Installation Code,

CAN/CSA B149.1

WARNING

Manufacturer recommends this condensing boiler be

vented with approved polypropylene venting material.

Use only materials listed below for vent pipe, intake

air pipe, and fittings. Failure to comply could result in

death or serious injury.

WARNING

Do not use cellular core pipe. Only specified sized

pipes are to be used. When using venting material

other than boiler manufacturer's venting, note the

correct installation procedure. Failure to follow these

instructions could result in death, or serious injury.

WARNING

•

Covering non-metallic vent pipe and fittings with

thermal insulation shall be prohibited.

•

Use of cellular core PVC for venting flue gas could

result in death, or serious injury.

• Coaxial venting shall be fastened with screws. Dual

flue venting is NOT fastened with screws.

Venting shall be properly supported.

Boiler shall not support any type of vent system.

All piping, glue, solvents, cleaners, fittings and

components must conform to ASTM and ANSI standards.

In Canada ULC S636 and in the USA UL 1738 schedule 40

CPVC are the only approved vent system to be used as an

alternative to polypropylene venting for the exhaust pipe.

Manufacturer requires use of a mechanical fastener at

every

push-fit gasket connection when using a single wall

polypropylene vent system.

Approved Polypropylene Manufacturers

* Natalini
* DuraVent

* Centrotherm
* Z-Flex

Note: Maximum equivalent length may vary between

manufacturers.

240013501 REV A [03/15/2022]

Содержание Dunkirk DCB-100
















































































































































Результаты поиска

Содержание Dunkirk DCB-100

Отзывы:

Бренды по названию

Популярные бренды

ECR International Dunkirk DCB-100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk DCB-100

Отзывы:

Бренды по названию

Популярные бренды