Ecoer EODA18H-2436 Скачать руководство пользователя страница 69

Страница: 69 / 82

Manufacturer reserves the right to change specifications or designs without notice.

10.2019

ESI (Ultra) Service Manual

www.ecoer.com

57/68

Error definition:

The defrost temperature (TH) sensor is short circuit or open circuit.

Possible causes:



Damaged main control board



The defrost temperature sensor is wrongly seated



Temperature sensor failure



There are other heat sources around the sensor

NOTE: Measure the DC voltage of the temperature sensor also works when outdoor unit powers on.

Display

Defrost temperature (TH) sensor is

disconnected or damaged

Check whether TH sensor is seated to the specified location and

connected to

CN4

on the main control board.

YES

Turn off the power supply, unplug the TH sensor to check if the

resistance is in the range of

Temperature sensor A

. *

NOTE

YES

Replace the main control board

Replace the sensor

Can the system go into backup running (SEG1 displays digital 6)?

Remove other heat source

Are there any other heat sources around the sensor?

Replace the sensor

Reconnect the sensor

Содержание EODA18H-2436



















































































Результаты поиска

Содержание EODA18H-2436

Отзывы:

Ecoer EODA18H-2436, Руководство по обслуживанию, Страница: 69 / 82

Результаты поиска

Содержание EODA18H-2436

Отзывы: