Eco-King HWB-299 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 124

background image

E93.1801EN171 HWB installation manual

31

8

THE HWB SANITAIRY SYSTEM: INSTALLATION INSTRUCTIONS

The HWB system

The system is set up as shown in the next two examples, the first showing a combination of one water heater and
one tank, the second showing a combination of two water heaters and two tanks. Other combinations are possible
as well, contact your supplier.

SAFETY COMPONENTS

NB!

The pictures show examples of functional installations. The safety components as shown in these pictures

are NOT necessarily conform all applicable standards and regulations.

ALWAYS have the installation installed by a skilled installer. Safety must be added according to all applicable
standards and regulations.

8.1.1

S

TAND

-

ALONE SET

-

UP

The basic form of an HWB installation is one water heater with one tank.
Shown in the picture are the principle components and connections.
Apply parameter configuration DHW-mode 4 (default, stand alone)

Example of a combination of one water
heater and one tank

Extra explanation:

1) Pressure relief valve (mandatory in case ser-

vice pipe pressure is too high)

2)  Inlet combination with valve (mandatory)
3)  Apply filter if necessary (recommended)
4)  A suitable safety valve must be mounted near

the water heater (mandatory)

This safety valve may never be isolated from
the water heater by means of a ball valve

5) Mount the tank sensor in an immersion bulb

into the tank at 1/5 from the bottom of the tank

6)  Drain valve (recommended)
7)  Hot and cold-water mixers

A)  Cold water inlet (service pipe)
B)  Hot water supply circulation
C) Circulation return

PUMP

NON- RETURN VALVE

VALVE

SAFETY VALVE

AUTOMATIC AIR VENT

FILTER

INLET COMBINATION
- Overflow
- Controllable Inlet valve
- Valve

PRESSURE REGULATING
VALVE

«
...
29
30
31
32
33
...
»

Содержание HWB-299





























































































































Отзывы:

Нет отзывов

Похожие инструкции для HWB-299

Бренд: Quooker Страницы: 12

Бренд: BN Thermic Страницы: 8

Бренд: DeLonghi Страницы: 4

UNI_SAUNA_B4.5KW

Бренд: UNIPRODO Страницы: 17

Бренд: ScaleBlaster Страницы: 8

164 002 12-US - UP3-P 12V

Бренд: Marco Страницы: 12

Бренд: Watson-Marlow Страницы: 12

105STS 90 -1.5"

Бренд: Canature Страницы: 94

Бренд: Heat-Flo Страницы: 20

TRV-220-220M-222

Бренд: Fagor Страницы: 26

Бренд: Daikin Страницы: 44

Бренд: Daikin Страницы: 12

Бренд: W. Tombling Страницы: 2

CENTRO-MATIC 85430

Бренд: Lincoln Страницы: 14

Flojet RLFP122202A

Бренд: Xylem Страницы: 40

Бренд: Wahl Bach Страницы: 12

Бренд: iGenix Страницы: 5

Бренд: Grundfos Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды