EcLine EC-PM-530D Series Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 82

EcLine EC-PM-530D Series Скачать руководство пользователя страница 62

EC-PM-530D User's Manual

- 55 -

USB Interface is 2.0 Full-Speed interface, and displayed as a USB port on the computer finally. User
can carry out USB printing by selecting corresponding USB port.

5.2.4 Serial Interface

EC-PM-530D printer’s serial interface is compatible with RS-232C protocol, supporting RTS/CTS
and XON/XOFF handshaking protocol. Its connector is a DB-9 type connector and pin number of
serial interface connector is shown as below.

Signal definition of each pin is shown as Table A-3:

The default settings of baud rate and data configuration in serial connecting way are 9600bps, 8 bits,
parity check disabled and 1 stop bit.

EC-PM-530D printer’s serial interface can be connected with the standard RS-232C interface. When
connecting with a PC, the connecting picture is shown as Figure 5-7. While connecting with an IBM PC
or a compatible PC, you can connect the cable as shown in Figure 5-8.

Pin

Number

Signal

From

Description

2 RXD

Host

Printer receives data from Host

3 TXD

Printer

Printer sends control code X-ON/X-OFF and
data to the Host

8 CTS

Printer

“MARK” state means printer is too busy to
receive data; “SPACE” means printer is ready to
receive data.

5 GND

—

Signal

GND

4

DTR

Printer

Data terminal is ready

Figure 5-5 Connection figure of printer and computer with USB interface

D0

D7

VBUS

GND

D+

D-

D0

PDIUSBD12

D7

Printer’s 26PIN connector

PDIUSBD12 chip

USB-B connector

Figure 5-6 Pin number of serial interface connector

Table A-3 Signal of the serial interface pin

Note:

①

“From” means the source where signal comes out.

②

The logical level of signal is EIA level.

5 1

9 6

«
...
60
61
62
63
64
...
»

Содержание EC-PM-530D Series



















































































Отзывы:

Нет отзывов