ECKELMANN Virtus 5 Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 183

background image

Firmware V7.16.x

16.05.2023

25/183

5.3 CAN Bus Station Monitoring

The controller cyclically checks the presence of all E*LDS components once they have been detected in the
system. If any component fails, this is detected by the station monitoring and the error message

"Computer

failure xxx"

is generated. Each new E*LDS component connected to the CAN bus is detected automatically by

the controller using "plug and play" and included in the station monitoring (Menu 2).

The connection to the system centre is made via the CAN bus interface:

The following CAN bus nodes can be present in the E*LDS system:

E*LDS components

CAN bus addresses

Max. number of E*LDS components in the
CAN bus

Case controllers
UA 300 and UA 400 series

1 .. 99

99

Pack controllers
VS 3010 / VS 3010 BS / VS 3010 CT / VS 3010 WP /
FS 3010 / VS 300 / VS 3010 C / VS 3015 C / VS
3015 CT

101 .. 109

9

System centre of the Virtus 5 series

111
127

1

system centre

and

1 integrated LAN gateway

AL 300 operator terminal

112 .. 116,
117 .. 120

9 or max. 5, if 4 receiver modules are present in
the system.

Receiver module WR 300
for wireless sensors TS 30 W / TS 30 XW

117 .. 120

4 (only possible if NO AL 300 operator terminal

uses these CAN bus addresses)

DDC modules of the GLT (building control)

122 .. 125

max. 4 if no Modbus TCP master gateways are
present in the system.

LDSWin PC via CAN bus to PC adapter

126

1

LDSWin PC via LAN gateway (version 1.1c and
higher)

126 or 127

1

If the system centre fails or is switched off, the operator terminal (if present) with the lowest CAN bus
address takes over the monitoring for the duration of the shutdown!



«
...
23
24
25
26
27
...
»

Содержание Virtus 5 Series
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtus 5 Series

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: VAT Страницы: 26

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: Gascat Страницы: 32

Бренд: Harsco Industrial Страницы: 57

Бренд: ICM Controls Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды