Echo U29515001001 Скачать руководство пользователя страница 49

Страница: 49 / 52

SRM-2320T

SPECIFICATIONS

X7732278302

SPECIFICATIONS

MODEL

SRM-2320T

Length without cutter head

1,795 mm (70.6 in.)

Width

250 mm (9.8 in.)

Height

329 mm (12.9 in.)

Weight (dry) w/o cutter head 5.3 kg (11.68 lb.)
Engine Type

Air cooled, two-stroke, single cylinder gasoline engine

Bore

32.2 mm (1.27in.)

Stroke

26 mm (1.02 in.)

Displacement

21.2 cc (1.29 in

Exhaust

Spark arrestor muffler or spark arrestor muffler with
catalyst

Carburetor

Diaphragm with purge pump

Ignition System

Flywheel magneto, capacitor discharge ignition type

Spark Plug

NGK BPMR8Y – Gap 0.6 mm (0.026 in.)

Fuel

Mixed (Gasoline and Two-stroke Oil)

Gasoline/Oil Ratio

50:1

Gasoline

Use 89 Octane unleaded. Do not use fuel containing
methyl alcohol, more than 10% ethyl alcohol or 15%
MTBE. Do not use alternative fuels such as E15 or E85.

Oil

ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345- FD,
two-stroke, air-cooled engine oil.

Fuel Tank Capacity

0.42 L (14.2 US fl. oz.)

Starter System

Automatic Rewind Starter

Clutch

Centrifugal Type

Vibration Isolated System

Rubber cushion on engine mount (heavy duty).
Rubber grip on front handle.

Operating Rod

25.0 mm aluminum tube

Drive Shaft

6.15 mm (.24 in) flexible shaft

Gear Case Ratio

2.07:1

Rotating Direction

Counterclockwise; viewed from top

Cutter Head

Speed Feed

400 LH Nylon line head,

Line capacity 6.0 m (20 ft.)

Handle

Front - loop, Rear handle

Shoulder Harness

Optional

Idle Speed

3,000 RPM

Clutch Engagement Speed

4,000 RPM

Wide Open Throttle Speed
(W.O.T.)

10,890 RPM

Содержание U29515001001





















































Результаты поиска

Содержание U29515001001

Отзывы:

Бренды по названию

Популярные бренды

Echo U29515001001, Руководство оператора

Результаты поиска

Содержание U29515001001

Отзывы:

Бренды по названию

Популярные бренды