background image

SRM-265ES

10-25L-0

1

1

2

1

INTRODUCTION

We are constantly working on technical

improvement of our products. For this reason,

technical data, equipment and design are

subject  to  change  without  notice.  All

specifications and directions in this SERVICE

DATA are  based  on  the  latest  products

information  available  at  the  time  of

publication.

CONTENTS

page

1 SERVICE INFORMATION .............................

2

1-1 Specification .................................................. 2

1-2 Technical data ................................................ 3

1-3 Torque limits ............................................... 4

1-4 Special repairing materials......................... 4

1-5 Service limits .............................................. 5

1-6 Special tools ............................................... 6

2 CARBURETTOR ADJUSTMENT PROCEDURE .

7

2-1 General adjusting rules .............................. 7

2-2 Presetting Idle adjust screw, idle mixture

needle and hi speed (H) mixture needle .............. 7

2-3 Adjusting carburettor .................................. 8

3 SERVICE HINT ..............................................

9

3-1 Reassebling 2 Nord-lock washers on Muffler ... 9

3-2 Adjusting throttle cable ................................ 10

3-3 Replacing crankshaft ................................... 11

Reference No.

 

10-25L-0

1

R E V I S E D :    2 0 1 0 0 1

ISSUED: 200708

Содержание SRM-265ES Series












Отзывы: