Echo CS-4510 Скачать руководство пользователя страница 53

Страница: 53 / 56

CS-4510

SPECIFICATIONS

X7503350603

Do not lend or rent your chain saw without the Operator’s
Manual.

Note:

• For future reference, you should keep this Operator’s Manual.

• If this Operator’s Manual becomes illegible or is lost, please contact

your ECHO dealer, or go to www.echo-usa.com.

SPECIFICATIONS

Model

CS-4510

Length

437 mm (17.2 in.)

Width

237 mm (9.3 in)

Height

298 mm (11.7 in.)

Dry weight

5.0 kg (11 lb.) Without chain and guide bar

Engine

Air-cooled two-stroke single cylinder

Displacement

45.0 ml (2.75 cu. in.)

Bore

43.0 mm (1.69 in.)

Stroke

31.0 mm (1.22 in.)

Compressions ratio

7.26:1

Carburetor

Diaphragm type

Spark plug

NGK BPMR8Y (Gap 0.65 mm [0.026 in.])

Fuel tank capacity

480 mL (16.23 US. fl. oz.)

Fuel / Oil Ratio

50:1

Gasoline

Use 89 octane unleaded. Do not use fuel containing
methyl alcohol, more than 10% ethyl alcohol or 15%
MTBE. Do not use alternative fuels such as E-15 or E-
85.

Oil

ISO-L-EGD (ISO/CD 13738) and JASO M345-FD
two-stroke, air-cooled engine oil.

Oiling system

Adjustable automatic oiler

Chain oil capacity

330 mL (11.16 US. fl. oz.)

Starter system

Automatic rewind starter

Clutch

Centrifugal type

Sprocket type

Spur type, 7-tooth, 3/8 in. pitch

Chain brake

Automatic band brake type

Idle speed

3,100 RPM

Clutch engagement speed

4,150 RPM

Содержание CS-4510

























































Результаты поиска

Содержание CS-4510

Отзывы:

Бренды по названию

Популярные бренды

Echo CS-4510, Руководство оператора

Результаты поиска

Содержание CS-4510

Отзывы:

Бренды по названию

Популярные бренды