Echo CS-4510 Скачать руководство пользователя | Manualshive

Страница: 32 / 56

background image

OPERATION

CS-4510

32

X7503350603

© 06/2019 ECHO Incorporated.

Note: Do not increase engine speed while chain brake is locked.

Severe brake damage will result.

Running

The saw chain should not move at idle, otherwise serious
personal injury may result.

Note: If saw chain moves adjust carburetor according to

“Carburetor Adjustment” instructions in this manual, or see
your dealer.

1.

After engine starts, allow it to return to
idle and warm up before using.

2.

Move chain brake lever fully
REARWARD to UNLOCK chain brake.

3.

Squeeze throttle trigger gradually and
increase engine speed.

4.

The chain starts running when the
engine reaches clutch engagement
speed (see technical data page).

5.

Confirm proper acceleration and
lubrication of chain and bar.

6.

Do not run the engine at high speed unnecessarily.

7.

Be sure that saw chain stops moving when throttle trigger is released.

Stopping

1.

Release throttle trigger and allow engine to idle.

2.

Push the momentary stop switch until the engine is stopped.

Note: If engine does not stop, pull choke control knob out fully to

stop engine.

Note: Return the unit to your authorized dealer to check and repair

stop switch before starting the engine again.

Shown with optional
Kick Guard

TM

Unlock Chain brake

«
...
30
31
32
33
34
...
»

Содержание CS-4510

























































Отзывы:

Нет отзывов

Похожие инструкции для CS-4510

Бренд: Narex Страницы: 44

Бренд: McCulloch Страницы: 20

Бренд: Echo Страницы: 68

Бренд: Poulan Pro Страницы: 36

Бренд: Baumr-AG Страницы: 36

Бренд: Echo Страницы: 64

Бренд: sunjoe Страницы: 60

Бренд: Jonsered Страницы: 35

Бренд: Jonsered Страницы: 40

Бренд: Jonsered Страницы: 37

Бренд: Jonsered Страницы: 40

Бренд: Jonsered Страницы: 80

Бренд: Jonsered Страницы: 4

Бренд: Jonsered Страницы: 32

Бренд: Homelite Страницы: 20

Бренд: Homelite Страницы: 20

Бренд: Homelite Страницы: 36

Бренд: Homelite Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды