Echo BEARCAT SC5540 Скачать руководство пользователя

Страница: 19 / 26

5 INCH CHIPPER/SHREDDER

ENGLISH

SERVICE & MAINTENANCE

WARNING

BEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE,

AND MAKE SURE ALL MOVING PARTS HAVE COME TO A COMPLETE STOP.

1. Remove the discharge door, discharge screen, belt

guards and rotor shaft end cap.

2. Loosen the bushing bolts holding the drive pulley to

the shaft and remove the pulley.

3. Loosen the set screw in the lock collars. Using a

punch and hammer, tap the lock collars in the opposite

direction of normal rotation. Remove the lock collars.

4. Loosen the set screw in the center of the rotor

assembly.

Remove the two 3/8" × 1/2" bolts running through the

rotor shaft.

6. Using a rubber mallet or other soft hammer, drive the

shaft towards the chipper chute side of the machine.

7. Once the shaft has been removed, the rotor assembly

can be removed through the discharge opening.

8. To ease reinstallation, smooth any divots or marks in

the shaft caused by the set screws. Clean the shaft as

much as possible before reinstalling into the machine.

5.12 REMOVING THE ROTOR

The rotor weighs in excess of 100 lbs. It is extremely

important to support the rotor to prevent it from falling

or shifting as the shaft is removed.

WARNING

5.13 PTO DRIVELINE LUBRICATION

Every 8 hours, lubricate PTO cross journals. Make

sure grease purges through all four bearings.

2. Every 8 hours, lubricate PTO inner tubes. Telescoping

members must have lubrication to operate

successfully. Telescoping members without fittings

should be pulled apart and grease should be added

manually with a brush.

3. Every 8 hours, lubricate the PTO shield retaining

bearing. Molded nipples on the guard near each

guard bearing are intended as grease fittings and

should be lubricated every 8 hours of operation.

To prevent personal injury or property damage:

Disconnect the PTO driveline from the source providing

power or disconnect the driveline from the chipper

and make sure that all moving parts have come to a

complete stop, before servicing, adjusting or repairing.

WARNING

Содержание BEARCAT SC5540



























Результаты поиска

Содержание BEARCAT SC5540

Отзывы:

Похожие инструкции для BEARCAT SC5540

Бренды по названию

Популярные бренды

Echo BEARCAT SC5540, Руководство пользователя

Результаты поиска

Содержание BEARCAT SC5540

Отзывы:

Похожие инструкции для BEARCAT SC5540

Бренды по названию

Популярные бренды