Echo Bear Cat SC5627B Скачать руководство пользователя страница 25

Страница: 25 / 30

5 INCH CHIPPER/SHREDDER/BLOWER

ENGLISH

Section

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

REMEDY

Engine will not start

Improper control settings

Use proper settings

Lack of fuel

Fill fuel tank

Spark plug disconnected

Connect spark plug

Dirty, stale or contaminated gas

Refill gas tank with fresh, clean unleaded

regular gasoline

Internal engine problems

See your dealer

Engine or rotor stalls or

stops

Obstructed discharge

Use branch or similar object to clear

discharge

Plugged rotor

Clear rotor. Feed material more evenly.

Feeding material that is too large

Reduce size of material

Chipper does not chip

Dull chipper blades

Rotate or sharpen blades

Drive belts loose or worn

Inspect drive belts, adjust or replace if

needed

Attempting to feed branches that are too

large

Limit branch size to 5 inches in diameter

Broken or missing chipper blades

Replace blade

Engine overheats

Cooling system plugged

Clean cooling fan and fins

Improper oil level

Fill engine to correct oil level. Refer to the

engine owners manual.

Engine runs, but dies

or does not accelerate

properly

Air filter dirty

Clean or replace

Fuel filter dirty

Replace

Fuel vent plugged

Clean or replace

Spark plug dirty/worn

Clean and adjust or replace

Carburetor vibration

Adjust

Cooling system dirty/plugged

Clean

Spark arrestor* plugged

Clean or replace

Hard to feed chipper;

requires excessive

power to chip

Dull chipper blades

Reverse or sharpen blades

Obstructed discharge

Use branch or similar object to clear

discharge

Improper blade clearance

Adjust clearance between chipper anvil and

chipper blades

Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in

this manual for the correct safety precautions and operating or maintenance procedures. Contact your dealer or ECHO

Bear Cat for service problems with the machine.

*If equipped

Содержание Bear Cat SC5627B































Результаты поиска

Содержание Bear Cat SC5627B

Отзывы:

Бренды по названию

Популярные бренды

Echo Bear Cat SC5627B, Руководство пользователя

Результаты поиска

Содержание Bear Cat SC5627B

Отзывы:

Бренды по названию

Популярные бренды