INPUT VOLTAGE ........................10 to 30 Volts DC.
INPUT CURRENT .......................0.5A @ 12.8V, 0.45A @ 25.6V
LIGHT OUTPUT ...........................AMBER: 160+ LUMENS
BLUE: 155+ LUMENS
RED: 123+ LUMENS
WHITE: 660+ LUMENS
CABLE LENGTH ..........................7 FT. (HEAD A), 4FT. (HEAD B)
LED ELEMENTS ..........................4 (EACH HEAD)
FLASH PATTERNS ......................16 (8 Standard, 8 optional cycle)
MAX NUMBER OF SYNC’D HEADS ... 64
WARRANTY PERIOD ..................5 YEARS
TECHNICAL SPECIFICATIONS
DIMENSIONS
INSTALLATION GUIDE
MOUNTING
Drill a 1” diameter hole in the reflector of the lens assembly.
A 1” hole saw is typically used. The HIDE-A-LED™ may be used as a
template to mark the location of the two screw holes. The W600 may
be mounted in either the back surface, bottom or sides of a reflector.
Drill pilot holes with a 7/64” drill bit. Install the HIDE-A-LED™ into the
lens assembly using the supplied gasket and screws. If the mount-
ing surface is curved additional sealing may be necessary. Use RTV
Silicone sealant if needed.
ELECTRICAL CONNECTIONS
The wiring diagram on page 2 shows a typical install.
RED:
+V
Connect to +V through an ON/OFF switch.
The use of a fuse located close to the voltage source is recommended.
Size the fuse according to the number of heads used in the system.
18AWG or larger wire is recommended.
BLACK:
- GROUND
Connect to - GROUND
vehicle chassis.
18AWG or larger wire is recommended.
BLUE:
Flash pattern SYNC and SELECTION wire.
If you wish to have all the LED heads synchronize
their flash timings and patterns with each other then all the BLUE wires
must be connected together(64 Heads Maximum).
The BLUE wire is also used to select the flash pattern.
Touch the BLUE wire to +V to select the next pattern in the FLASH
PATTERN LIST. The BLUE wire can also be run to a momentary
push-button located on the dashboard to allow the flash pattern to be
changed when desired.
Note: Do not connect the BLUE wire to - Ground.
It will disrupt the flash pattern sync signal.
PAGE 1
920-9121-00 REV. C
DEUCE
LED HEAD
POWER MODULE
833 W. Diamond St Boise, Idaho 83705
TEL: 888-844-6682 www.strobe.com
THE HEATSINK WILL BE HOT AFTER RUNNING
FOR AN EXTENDED PERIOD.
DO NOT TOUCH.
IT
WILL NOT
MELT ANY OF THE PLASTIC
PARTS OF THE LENS ASSEMBLY.
STRAP THE WATERPROOF
POWER MODULE TO THE BODY
OF THE VEHICLE
AWAY FROM
ANY HIGH HEAT SOURCES.
! HOT !
GASKET
REFLECTOR
DO NOT DRILL HOLES THROUGH THE POWER MODULE!
1” HOLE
7/64” PILOT
HOLES
SCREWS
TIP: APPLY RTV SILICONE
TO THE SCREWS TO SEAL
THE THREADS.
LOCATE LED HEAD AT LEAST 1” AWAY
FROM ANY FACTORY BULB!
FOR DUAL WALL REFLECTORS: FIRST USE A 1.5” HOLE SAW TO DRILL THROUGH OUTER
LAYER ONLY. THEN USE 1” HOLE SAW TO DRILL THROUGH INNER LAYER USING SAME
PILOT DRILL HOLE. INSTALL THE LED HEAD THROUGH THE 1.5” HOLE AND SEAL THE GAP
WITH RTV SILICONE.
DUAL HEAD W600
1
SYNC
TM
1.50"
0.875"
1.28"
0.150"
0.980"
1.50"
4.89"
"5
9.
0
0.59"
HEAD A
HEAD B
INPUT MABLE: 4FT
LED HEAD
CABLES:
4FT, 7FT
CONNECTOR SEALING
