background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E180-Z5812SP Product Manual

Copyright ©2012–2019,

Chengdu Ebyte Electronic Technology Co., Ltd.

27

When the node is powered on, it will join the network (if there is no network status) or restore the network (if there is a network
without parent node status) in the Rejoin period cycle. When the node detects that the parent node is offline during operation, it
will reconnect with the “Rejoin period” period.

When the parameter is 254, it means that no reconnection or periodic network screening will be performed.

6.6.17 Maximum number of attempts to reconnect

Read instruction format:

command format

command example

send

FE 01 30 FF

return

FB 30 net_rejoincount

send

FE 01 30 FF

return

FB 30 05

Configuration command format

command format

command example

send

FD 01 30 time FF

return

FA 30

send

FD 01 30 05 FF

return

FA 30

Rejoin maxcount: (1~254) The maximum number of reconnections ranges from 1 to 254 times, and the default is 10

After the node loses its parent node during operation or has a network without a parent node, try the maximum number of rejoins

after power-on. If the previous network has not been restored, the previous network information will be cleared, and the new
network will be periodically scanned to join with the Rejoin period. Scanning for a new network consumes more power than
restoring the previous network.

When the parameter is 254, it means that when there is a network and no parent node, the reconnection is always performed and
the action of clearing the network is not performed.

6.6.18 Wireless remote configuration ID

Read instruction format:

command format

command example

send

FE 02 31 FF

return

FB 31 header

send

FE 02 31 FF

return

FB 31 A8 8A

Configuration command format

command format

command example

send

FD 02 31 header FF

return

FA 31

send

FD 02 31 A8 8A FF

return

FA 31

Содержание E180-Z5812SP




































Отзывы: