EBS EBS 2600 Скачать руководство пользователя

Страница: 149 / 184

149 of 184

EBS‑2600 User Man

ual

G2023/04/26_1EN

2023.05.16

8. PERIODIC MAINTENANCE

The objective of periodic maintenance is to ensure reliable operation of the printer.

8.1. PURGING/VENTING THE PRINTHEAD

Purging functions are not available to

operator

‑type users.

The printhead purging/venting can be done by

instructed persons

Printhead purging/venting is disabled if the printer reported a warning about critically low ink in the bot

tle.
Tools required:

‑ a sprayer with wash‑up (Part No.

XS21602

‑ protective gloves that are resistant to ink/wash‑up,

‑ safety goggles,

‑ absorbent material or a metal vessel for collecting waste,

‑ a cross head screwdriver,

‑ optional drip molding (an accessory; Part No.

P513324

The objective of printhead purging/venting is to:

–

Improve print quality by clearing slightly clogged nozzles and cleaning the nozzle plate in the print

head,

–

Vent the printer after it has been transported or a bottle has been replaced.

The purging/venting consists of the opening of all nozzles at the same time and jetting of ink through
the nozzles under pressure.
The jetted ink flows down the nozzle plate (optionally along drip molding

- see

Fig. 62 on page 150

)

to drip rail

, and then it is collected by the drip system and reaches waste bottle

Two printhead purging/venting modes are available:

–

short purging lasting about

2 seconds

–

long purging lasting about

85 seconds

It is advisable to follow the printhead purging/venting procedure with the application of optional drip
molding

, which is part of a double‑sided accessory (Part No.

P513324

). If no drip molding is used,

the ink outlet from the printhead (from the nozzle plate) must be secured with absorbent material.

To prepare the printer for the printhead purging/venting procedure

with the use of an optional drip

molding

(the recommended method):

1. If the printer is printing, press the

icon on menu bar

(see

Fig. 43 on page 52

) on the main

screen to pause printing.

Содержание EBS 2600

























































































































































































Результаты поиска

Содержание EBS 2600

Отзывы:

Похожие инструкции для EBS 2600

Бренды по названию

Популярные бренды

EBS EBS 2600, Руководство пользователя

Результаты поиска

Содержание EBS 2600

Отзывы:

Похожие инструкции для EBS 2600

Бренды по названию

Популярные бренды