background image

 

CPX200NB ALARM CONTROL UNIT – INSTALLER MANUAL  

 

  25 / 116 

5.6.

 

ALARM DISPLAY 

If red ALARM LED flashes when the system is armed, it means that while you were absent 
some alarms occurred (numbers of lines that initiated them will be displayed as well) which 
have already ceased. But, if ALARM LED emits constant light, it means that system still is in 
alarm state. Exercise caution! If you suspect any intruder to be present in the facility, leave 

the facility immediately and call security guards.  

5.7.

 

ALARM MUTE 

1.

 

To mute (deactivate) the alarm, enter the code and press 

. 3 beeps will confirm the 

code. Also, the system will be disarmed. 

2.

 

In order to identify the alarm type, please refer to 

Alarm Memory chapter of the present 

manual. 

5.8.

 

ALARM MEMORY 

 

  - Display of alarm memory 

 
The function displays the history of alarms that occurred in the system. When the function is 
activated, ALARM and PROG LEDs are flashing slowly and all alarms that occurred since last 
arming are displayed. LEDs 1 - 7 display the information from which zones the alarm was 
activated.  To  clear  the  alarms  memory,  press 

.  To  exit  without  clearing  the  alarms 

memory, press 

Alarm source types: 

Diodes 1 to 7 – Sabotage of lines 1 to 7 
 

If no diodes are on and the ALARM led is blinking, then there alarms that were triggered by 
the  source  other  than  input  lines. 

Other  alarms  history  can  be  accessed  by  selecting 

following code from the main menu: 

After  pressing  the  button  corresponding  to  active  LED,  the  detailed  information  about  the 
alarm source within selected type is displayed. 

Pressing 

 will result in return to the main menu. 

 

Other alarm source types: 

2 – Keypads tamper 
3 – Emergency button used 

Other alarm source types -> Keypads tamper: 

1 – Keypad tamper 1 
2 – Keypad tamper 2 
3 – Keypad tamper 3 

Other alarm source types -> Emergency button used: 

1 – Fire alarm activated 

Содержание CPX200NB





















































































































Отзывы: