background image

 

CPX200N ALARM CONTROL UNIT – INSTALLER MANUAL  

 

  54 / 106 

8.1.2.2.

 

User ID 

Most  often  it  is  not  required  while  using  public  APN.  For  private  APN,  you  should 
obtain that parameter from the operator (without it no access to GPRS network can 
be granted).  

8.1.2.3.

 

User password 

Most  often  it  is  not  required  while  using  public  APN.  For  private  APN,  you  should 
obtain that parameter from the operator (without it no access to GPRS network can 
be granted).  

 

NOTE: Using private APN increases the system security. 

8.1.2.4.

 

DNS1 and DNS2 

It  defines  the  address  of  primary  and  secondary  DNS  (Domain  Name  System).  If 
server  address  was  entered  as  a  domain  name  at  least  one  DNS  address  must  be 
entered. 

8.1.3.

 

Primary Server Parameters 

8.1.3.1.

 

Server IP Address 

It  is  the  IP  address  of  a  monitoring  system  receiver  (OSM.2007)  or  a  computer  on 
which “Communication server” software is installed, e.g. 89.123.115.8.  The address 
can be given as a server’s domain name, e.g. modul.gprs.com. In such a case at least 

one DNS server address is required. 

8.1.3.2.

 

Server port 

It defines a port which was dedicated in the server for the receipt of  data from the 

equipment.  

8.1.3.3.

 

Interval between subsequent attempts of establishing connection 

with a server. 

The  programmed  equipment  with  SIM  card  inserted  will  automatically  attempt  to 

establish connection with a server. Here you can define an interval (in seconds) after 
which the equipment will retry to connect with a server, in case the previous attempt 
was unsuccessful.  

8.1.3.4.

 

Number of attempts of establishing connection with a server. 

You can define how many times the equipment will try to connect with the server in 
case  of  subsequent  faults.  After  a  defined  number  of  attempts,  the  equipment  will 
initiate the procedure of connecting with secondary server. The option is active only 

in case the secondary server parameters were defined. 

Содержание CPX200N











































































































Отзывы: