EBS Active Track Basic+ Скачать руководство пользователя страница 54

Страница: 54 / 55

14.

Technical parameters

GSM module

Modem

u-blox SARA-G350

Electrical characteristics

Power supply

5V/1A

Power socket

standarized Micro USB type B plug

Main battery (Li-Polymer), charge time

1700 mAh, 2,5 hours

Backup battery (Li-Polymer)

60mAh

Battery working time

up to 72 hours* (AT2-G-2G, AT2-GR-2G)

up to 168 hours** (AT2-R-2G)

up to 50 hours* (AT2-GR-3G)

Physical characteristics

Dimensions (HxWxT)

121 x 60 x 30 mm

Casing durability

The waterproof and shock resistant housing, IP67

Weight

155g (AT B+); 30g (charger)

Motion sensor

3-axis motion sensor (accelerometer)

RFID reader (optional)

Reader type

Proximity RFID

RFID reader frequency

125 kHz

RFID read-out distance

3-4 cm (depends on transponder type)

Interfaces & general features

Internal speaker and microphone

4 Buttons for easy operating

Ambient operating temperature

-20°C do +55°C***

Ambient operating humidity outside the charger

5% do 100%

Ambient operating humidity inside the charger

8% do 90%

Data transmission via GPRS (TCP, IP), SMS

Remote administration & firmware update

Configuration

Local: PC through RS232 link (LX cable and AGP3 programmer required)

Remote: via GPRS, SMS, CSD

Events buffer size

1000

Quantity of system events stored in history

8000

Содержание Active Track Basic+
























































Результаты поиска

Содержание Active Track Basic+

Отзывы:

Похожие инструкции для Active Track Basic+

Бренды по названию

Популярные бренды

EBS Active Track Basic+, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Active Track Basic+

Отзывы:

Похожие инструкции для Active Track Basic+

Бренды по названию

Популярные бренды