EBS Active Track Basic+ Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 55

background image

32

Using the "Restore defaults" link it is possible to return to the manufacturer's

recommended settings, how to send events to the supervisory software.

Note:

“Configuration changed” event refer to configuration changes made by SMS or

GPRS commands.

7.2.3.4.1.1.

GPRS On / GPRS Off

In this column you define signals that are to be reported to monitoring station with

GPRS transmission.
To transmit any signal you should only click it (proper square on your right).

Click on [Clear] button to remove all marked signals.

Click on [Invert] button to change markings to contrary.

7.2.3.4.1.2.

Send a PANIC signal as soon as possible

If this option is enabled, the device will connect to the server after pressing the
"Panic" button and report the PANIC event first (and all other events stored in the

device's memory) regardless of the current operating mode.

7.2.3.4.2.

Additional data

The Additional data functionality allows for defining kinds of additional data which will
be transmitted together with events to monitoring station via GPRS. The data may
become valuable information about device's work conditions though it may increase

amount of bytes sent through GSM network. It is possible to define two separate sets

«
...
30
31
32
33
34
...
»

Содержание Active Track Basic+
























































Отзывы:

Нет отзывов

Похожие инструкции для Active Track Basic+

Бренд: Garmin Страницы: 2

Бренд: Garmin Страницы: 16

Бренд: CyBike Страницы: 2

Бренд: FineDigital Страницы: 44

Бренд: WANWAY TECH Страницы: 10

Бренд: Tele System Страницы: 56

Dimension4 UWB+BLE Tag

Бренд: Ubisense Страницы: 20

Бренд: Lkgps Страницы: 6

Бренд: RoyalTek Страницы: 31

Бренд: Acer Страницы: 68

Бренд: Acer Страницы: 39

Бренд: Acer Страницы: 85

Бренд: Acer Страницы: 68

Бренд: Acer Страницы: 98

CoPilot Pocket PC6

Бренд: Acer Страницы: 64

Бренд: UPS Aviation Technologies Страницы: 82

Бренд: Recon Dynamics Страницы: 6

Бренд: Transystem Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды