Eaton VORAD AlwaysAlert Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 30

background image

16

Component Installation

Wiring Harness

Installation

Wiring Harness Installation

Installation of the wiring harness should start from the CPU and then extend outward to the other components.

Avoid routing the wiring harness near sharp edges or extreme heat, which could damage wire insulation.

Route the wires along existing wires, up through existing pass-through holes or spaces in the floor or dashboard to the
installed components. Coil up the slack in the wire harness and store it neatly behind the dashboard or kick panels,
depending upon the location of the CPU. The following illustration shows a typical installation of the wiring harness.

Note: Use the protective loom where necessary. Tie-wrap the harness for a secure/neat installation.

1 - Driver display unit
2 - Side sensor display
3 - To side sensor and antenna assembly

4 - Central Processing Unit
5 - Ground strap

CAUTION

2

1

3

4

5

«
...
17
18
19
20
21
...
»

Содержание VORAD AlwaysAlert































Отзывы:

Нет отзывов

Похожие инструкции для VORAD AlwaysAlert

Бренд: Oki Страницы: 2

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Porsche 911 Turbo S Wheel

Бренд: FANATEC Страницы: 9

Бренд: FANATEC Страницы: 35

Line FP7000 Housing

Бренд: Fantasea Страницы: 5

Бренд: Fantasea Страницы: 5

Бренд: Fancom Страницы: 49

Бренд: FANATEC Страницы: 2

Бренд: Hach Страницы: 44

Бренд: Habasit Страницы: 14

smartsensor advance

Бренд: Wavetronix Страницы: 2

Бренд: X-lite Страницы: 5

Бренд: M-Audio Страницы: 14

Бренд: YUNEEC Страницы: 6

KTS-WB61141142 Series

Бренд: SICK Страницы: 8

Бренд: Kodak Страницы: 2

Бренд: Subaru Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды