Eaton Power Xpert XGIS Скачать руководство пользователя страница 30

Страница: 30 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Table 4. Relevant standards

Relevant standards

IEC 62271-100

High-voltage switchgear and controlgear - Part 100: Alternating current circuit breakers

IEC 62271-102

High-voltage switchgear and controlgear - Part 102: Hi-voltage alternating current three-position disconnect switches and earthing switches

IEC 62271-200

High-voltage switchgear and controlgears - Part 200: AC metal-enclosed switchgear and control gear for rated voltages above 1 kV and up to and

including 52 kV

IEC 60529

Degrees of protection provided by enclosures (IP code)

IEC 62271-1

High-voltage switchgear and controlgear - Part one: Common specifications

Table 5. Operating conditions

Normal operating conditions, according to IEC 62271 – 1 for indoor switchgear

Ambient air temperature

≤

40° C

≤

35° C on average over 24 hours

≥

-5° C

Altitude

≤

1000 m

Contact Eaton for applications above 1000 m.

Atmosphere

No dust, smoke or corrosive or inflammable gas or vapor, or salt (clean industrial air)

Storage conditions

To retain all of the functional qualities when stored for prolonged periods, we recommend that the equipment be stored in its original packaging,

in well-ventilated, clean, and dry conditions, sheltered from the sun and rain, at a temperature > -25° C and < +55° C.

Figure 57

shows outlines and dimensions for the 1250 A XGIS vertical

section.

Figure 58

shows outlines and dimensions for the 2000 A and 2500 A

XGIS vertical section.

Содержание Power Xpert XGIS

















































































Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Бренды по названию

Популярные бренды

Eaton Power Xpert XGIS, Инструкция пользователя

Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Бренды по названию

Популярные бренды