Eaton MENVIER30 Скачать руководство пользователя страница 43

Menvier30 

Technical Specification 

 

 

Page 39 

Transmitter 
range 

The range of the transmitters 
compatible with this control unit 
depends on the environment in 
which they are installed. As a 
guideline, most transmitters will 
work at in excess of 200m 
range in free space conditions. 

Compliance Statements 

The Menvier30 is compliant with EN50130-5 
environmental class II. 

The Menvier30 is suitable for use in systems 
designed to comply with PD 6662: 2010 at grade 
2. 

When fitted with radio devices the Menvier30 is 
capable of compliance with EN50131 at Grade 2. 

The built in communicator is compliant with 
EN50136-1 as an ATS2 communicator. 

At Grade 2 the built in communicator provides a 
compliant communicator for the Menvier30 
provided that: 

a)  It is connected in accordance with the 

installation instructions. 

b)  The connected PSTN is functioning normally. 

When using its built in communicator this product 
provides options A, B and C at Grade 2 as noted 
in Table 10 of EN50131-1:2006+A1:2009. 

If the installer selects a non-compliant 
configuration then they must remove or adjust 
compliance labelling. 

Compatible Equipment 

HUD 

705rEUR-00 

Two button HUD (single 
channel, top button is 
disabled) 

706rEUR-00 

Two button HUD/tilt switch 
transmitter 

710rEUR-00 

Two button HUD 

726rEUR-50 

Long range hand held HUD 

726rEUR-60 

Short range hand held HUD 

Detectors 

713rEUR-00 

Pet tolerant PIR 

714rEUR-00 

PIR Transmitter (Small case) 

720rEUR-00 

Smoke Detector Transmitter 

734rEUR-00/01 

CC/FSL Door Contact 
Transmitter (white) 

734rEUR-05/06 

CC/FSL Door Contact 
Transmitter (brown) 

738rEUR-00/04 

Spyder shock sensor 
(white/brown) 

739rEUR-50 

Sentrol glass break detector 

DET-RDCS 

Combined door contact 
shock sensor transmitter 

XCELR 

Radio PIR 

XCELRPT 

Pet tolerant radio PIR 

XCELW 

Wired PIR 

XCELWPT 

Pet tolerant wired PIR 

Sounders 

760ES 

External Wireless sounder 

9040UK-00 

Speaker boxed 

Setting / Unsetting 

– Keypads 

i-rk01 

Radio Keypad 

i-kp01 

Keypad (with internal prox 
reader, but without zones or 
external prox reader) 

KEY-EP 

External prox reader for 
KEY-KPZ01 

KEY-K01 

keypad, without zones or 
internal prox reader  

KEY-KP01 

keypad with internal prox 
reader and terminals for 
external prox reader  

KEY-KPZ01 

keypad, with internal prox 
reader, two zones, one 
output and terminals for 
external prox reader 

Setting / Unsetting - Fobs 

FOB-2W-4B 

Two-way keyfob 

i-fb01 

Four button remote control  

727rEUR-00 

Four button remote control 
with encrypted code (HUD 
function not compatible with 
BS8243 or DD243) 

Communicators 

i-dig02 

PSTN Communication (ARC 
only). 

i-gsm02 

GSM communications 
module 

i-sd02 

PSTN Communication 
module with speech dialling 

Accessories 

703rEUR-00 

4-channel (2 zone) 
transmitter 

762rEUR-00 

Two Channel Receiver 

768rEUR-50 

Eight Channel Receiver 

770rEUR-00 

Wireless Accessory Module 

771rEUR-00 

Info Module 

i-rc01 

Relay Card 

Содержание MENVIER30













































Отзывы: