Eaton Matrix Telecom Inverter System Скачать руководство пользователя страница 44

Страница: 44 / 86

Matrix Telecom Inverter System

IPN 997-00012-68D February 2010

STS Parameter Settings

Parameter Setting

Option

AC HL: High loss of alternative AC input xxxV

AC LL: Low loss of alternative AC input

xxxV

Inv HL: High loss of inverter AC input

xxxV

Inv LL: Low loss of inverter AC input

xxxV

Priority

Selectable at 1) On line or 2) Off line

Fan speed

Normal speed / Full speed

Alarm Settings

In “clear” menu, push

to clear the alarm history.

Connection to Dry contact Relays

Use # 30~16 AWG to connect to the dry relay contacts.

Dry Contact Relay Setting

To use the dry relay contacts as alarms, set the alarm mode of each dry contact as follows:

Step 1 - Select which dry contact you want use

In the "Setting" menu, select "system", select "Dry contact", Select Dry contact # using

and .

Step 2 - Select the module for each the dry contact

At "Alarm Type" press

, select the module alarm for this Dry contact, then press

Содержание Matrix Telecom Inverter System















































































Результаты поиска

Содержание Matrix Telecom Inverter System

Отзывы:

Похожие инструкции для Matrix Telecom Inverter System

Бренды по названию

Популярные бренды

Eaton Matrix Telecom Inverter System, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Matrix Telecom Inverter System

Отзывы:

Похожие инструкции для Matrix Telecom Inverter System

Бренды по названию

Популярные бренды