Eaton Magnefix MD4 Скачать руководство пользователя страница 81

Страница: 81 / 109

Magnefix MD4

991.184 G01 03

4.4 Resetting an overcurrent indicator

A switch cap can be provided with an indicator (a) for

passing short-circuit currents. The switch cap has a small

round window showing the rated value of the breaking

current.

The moment the current passing through the switch cap

exceeds the value to which the indicator has been set, a

red flag appears in the window of the switch cap.

4.4.1

Electromechanical overcurrent

indicator

In order to reset the electromechanical overcurrent

indicator, a magnet has been supplied.

Procedure

1. Eliminate the overcurrent condition.

2. Slide the magnet through the slot at the front of the

switch cap.



The red flag disappears.



The overcurrent indicator has been reset.

4.4.2

Electronic overcurrent indicator

Once the overcurrent condition has ceased to exist, the

electronic overcurrent indicator resets itself:



either immediately, if the system stays live;



or some minutes (up to 30) after system voltage

recovery (after the overcurrent condition has ceased

to exist).

4.5 Protective relay operation

For adjustment and operation of the protection relay please

refer to the corresponding manual. This manual is part of

the information pack supplied.

Содержание Magnefix MD4














































































































Результаты поиска

Содержание Magnefix MD4

Отзывы:

Бренды по названию

Популярные бренды

Eaton Magnefix MD4, Руководство пользователя

Результаты поиска

Содержание Magnefix MD4

Отзывы:

Бренды по названию

Популярные бренды