Eaton Magnefix MD4 Скачать руководство пользователя страница 67

Страница: 67 / 109

Magnefix MD4

991.184 G01 03

3.9 Connection of plastic-insulated cables to

Protected panels

3.9.1

Plastic-insulated cable with copper

core up to 3 x 70 mm

ARNING

•

Always earth the installation.

•

Never work on a live or partly live installation.

Required materials



3 insulating conduits (a)



1 bag containing greased rubber sleeves (b)



3 sealing plugs (c)



3 protection tubes (d)



18 plastic screws (e)



3 cable core clamps (universal)



plastic cable clamps (j)

Cable box for plastic-insulated cable 3 x 70 mm

OTE

•

Universal cable core clamps are only suitable

for connecting copper cable cores.

•

Terminate the cable cores in accordance with

the cable manufacturer’s instructions.

Universal cable core clamps, Cu, up to 70 mm

Содержание Magnefix MD4














































































































Результаты поиска

Содержание Magnefix MD4

Отзывы:

Бренды по названию

Популярные бренды

Eaton Magnefix MD4, Руководство пользователя

Результаты поиска

Содержание Magnefix MD4

Отзывы:

Бренды по названию

Популярные бренды