background image

Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]

1

PACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE

Instruction Manual/Manuel d’instructions/Instrucciones

Lumark

 ENGLISH

LEL10BPCI

(Bronze/Bronze/Bronce)

LEL10WPCI

(White/Blanc/Blanco)

A.

 Light fixture

  Appareil  d’éclairage    
  Accesorio

C.

  (2) #6 and (2) #8 junction box screws 

   (use the size that fits your junction box)
   (2) Vis nº 6 et  2 vis nº 8 pour boîtier de  

   jonction (choisissez la dimension convenant  

   à votre boîtier de jonction)
   (2) Tornillos #6 y (2) tornillos #8 para 

   montaje de la caja de conexión  

  

(utilice el tamaño que mejor se  

   adecue a su caja de conexión)

E.

  (3) Wire nuts

   (3) Capuchons de connexion
   (3) Conectores

   de cable

B.

   Mounting bracket

  Support de montage
  Soporte de montaje

D.

  Threaded mounting rod

  Tige de fixation filetée
  Varilla roscada para 

 montaje

F.

  Cap nut

  Écrou borgne
  Tuerca tapa

IITEMS REQUIRED

 

(Purchase separately)

•  Phillips screwdriver
•  Weatherproof silicone caulk

IMPORTANT SAFETY INSTRUCTIONS

  When using product, basic precautions should always be followed, including the following:

•  Heed all warnings, including below warnings AND those included on product.
•  Save these instructions and warnings.
•  For outdoor use only.
•  cULus LISTED for wet location.
•  Your fixture is prewired and preassembled for easy installation.

•  Read and follow these instructions.
•  Risk of fire/electric shock. If not qualified, consult an electrician.
•  Disconnect power at fuse or circuit breaker before installing or servicing.

CAUTION

•  Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids 

the warranty.

•  Fixture should be installed by persons with experience in household wiring or by a 

qualified electrician. The electrical system, and the method of electrically connecting 

the fixture to it, must be in accordance with the National Electrical Code and local 

building codes.

•  Fixture designed for wall mount to a recessed junction box only. Install fixture to 

junction box marked for use in wet locations.

•  This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may cause 

undesired operation. Under Part 15   of the FCC Rules, any changes or modifications 

to the fixture described in this instruction sheet that are not expressly approved by 

Cooper Lighting, LLC could void the user’s authority to operate the equipment.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

•  Install patio light 7-10 feet above the ground.
•  Do not mount fixture close to reflective surfaces such as windows, white walls, white 

surfaces and water.

•  When installing two fixtures on one switch, make sure the switch is rated for at least 

a 1 A inductive load.

WARNING

MOUNTING YOUR FIXTURE

NOTE:

 Do not mount within 2 feet of a highly reflective 

exterior inside corner (Fig. 1).
1.

 

 

Turn off the power at the main fuse/breaker box.

2.   Attach mounting bracket (B) to junction box with 

two screws (C) provided (Fig. 2).

3.   Screw the threaded mounting rod (D) into the 

center of the mounting bracket (B) until the  

threads are showing on the back side of the  

mounting bracket (B) (Fig. 3).

WIRING YOUR FIXTURE

1.

 

 

Turn off the power at the main fuse/breaker box.

2.   Connect the black fixture wire to the black supply 

wire (hot) using wire connector (E) (Fig. 4).

3.   Connect the white fixture wire to the white supply 

wire (neutral) using wire connector (E) (Fig. 4).

4.   Connect the copper ground fixture wire to an 

appropriate supply ground or a grounded  

junction box.

NOTE: Be careful to connect the wires correctly. 

Make sure no bare strands of wire extend from the  

wire connector (E) provided or other approved wire  

connectors (not provided).
5.

 

  Attach fixture to the threaded mounting rod (D).

6.

 

  Secure with cap nut (F) (Fig. 5).

7.   Add silicone caulk around fixture to help maintain a 

weather-resistant seal.

2 ft.

2 ft.

2 ft.

1

2

Junction box

C

C

B

3

Junction box

D

B

5

Junction box

D

F

A

4

Junction box

D

E

E

A

Отзывы: