Eaton IBC-SW, Руководство по установке, Страница: 50 / 68

42 Eaton 93PM Integrated Battery Cabinet-Small Welded (IBC-SW) Installation Manual 164000639—Rev 03
2. Line-Up-and-Match Wiring. Route the battery shunt trip interface wiring from the UPS battery shunt trip
interface terminals through the bottom inter-cabinet access pass-through (see Figure 9 ) of the UPS cabinet
and IBC–SW to the wiring channel on the left side of the IBC–SW (see Figure 12 ). Route the wiring along
the wiring channel to the IBC–SW battery interface terminal block TB2. See Figure 17 for terminal
locations. See paragraph 3.2.3 IBC–SW Interface Wiring Preparation , Table 7 , and Figure 18 for wiring and
termination requirements. Refer to the applicable Eaton 93PM UPS Installation and Operation manual
listed in paragraph
1.7 For More Information , for UPS cabinet terminal locations.
3. Secure the interface wiring to the wire tie anchors (see Figure 14 ) using Zip ties.
4. Proceed to Step 11 .
5. Top Entry Wiring. Remove the top conduit plate (see Figure 16 ) from the top of the IBC–SW. Identify all
conduit requirements and mark their location. Drill and punch all conduit holes in the top conduit plate prior
to mounting on the IBC–SW. Install the conduit plate and install all conduit runs into the plate. Pull the
wiring through the conduit into the wiring area.
NOTE In multiple IBC–SW installations, route the battery interface wiring between IBC–SWs
through the top of the adjacent IBC–SW using the top side inter-cabinet access pass-
through (see
Figure 9 ).
6. Route the battery shunt trip interface wiring from the UPS battery shunt trip interface terminals through
top of the IBC–SW to the IBC–SW battery interface terminal block TB2. See
Figure 17 for terminal
locations. See paragraph 3.2.3 IBC–SW Interface Wiring Preparation , Table 7 , and Figure 18 for wiring and
termination requirements. Refer to the applicable Eaton 93PM UPS Installation and Operation manual
listed in paragraph
1.7 For More Information , for UPS cabinet terminal locations.
7. Proceed to Step 11 .
8. Bottom Entry Wiring. Remove the bottom conduit plate (see Figure 16 ) from the inside bottom of the
IBC–SW. Identify all conduit requirements and mark their location. Drill and punch all conduit holes in the
bottom conduit plate prior to mounting on the IBC–SW. Install the conduit plate and install all conduit runs
into the plate. Pull the wiring through the conduit into the wiring areas.
NOTE In multiple IBC–SW installations, route the battery interface wiring between IBC–SWs
through the top of the adjacent IBC–SW using the top side inter-cabinet access pass-
through (see
Figure 9 ).
9. Route the battery shunt trip interface wiring from the UPS battery shunt trip interface terminals through
the bottom of the IBC–SW to the wiring channel on the left side of the IBC–SW (see
Figure 12 ). Route the
wiring along the wiring channel to the IBC–SW battery interface terminal block TB2. See Figure 17 for
terminal locations. See paragraph 3.2.3 IBC–SW Interface Wiring Preparation , Table 7 , and Figure 18 for
wiring and termination requirements. Refer to the applicable Eaton 93PM UPS Installation and Operation
manual listed in paragraph
1.7 For More Information , for UPS cabinet terminal locations.
10. Secure the interface wiring to the wire tie anchors (see Figure 14 ) using Zip ties.
11. Connect the battery shunt trip interface wiring to the IBC–SW battery shunt trip interface terminals. See
paragraph 3.2.3 IBC–SW Interface Wiring Preparation and Table 8 for termination requirements.
For a detailed view of the IBC–SW terminal block, see Figure 19 .
12. Connect the battery shunt trip interface wiring to the UPS battery shunt trip interface terminals. Refer to
the applicable Eaton 93PM UPS Installation and Operation manual listed in paragraph
1.7 For More Information , for UPS cabinet termination requirements.
NOTE In the following step, if the safety shield cannot be reinstalled because of misalignment,
use the leveling feet to realign the cabinet.
Installation