Eaton Fuller FSO-2405 страница 133 Скачать руководство пользователя

Страница: 133 / 163

133

Front Section Disassembly

FSO-2405

2nd Ed. 02/07

Front Section

FSO-2405/62

FSO-2405/63

FSO-2405/61

FSO-2405/45

Reverse Shifting Interlocking System

Assembly

1. Align the interlok pin hole with the housing hole

and install the interlocking mechanism into the
pin bore.

2. Give the spring as much as the tension you

can by winding the spring on the pin and then
set its free end in the housing hole.

3. Install a new roll pin.

NOTE: Use a 4 mm diameter pin punch.

NOTE: Replace the roll pin by a new one.

4. Install a new expansive plug in the housing

hole.

NOTE: See “Expansive Plugs” for
instructions.

Содержание Fuller FSO-2405




































































































































































Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды

Eaton Fuller FSO-2405, Руководство по обслуживанию

Результаты поиска

Содержание Fuller FSO-2405

Отзывы:

Похожие инструкции для Fuller FSO-2405

Бренды по названию

Популярные бренды