background image

1 General information – EMS2 electronic motor starter

1.1 Standards

EMS2… Electronic motor starter

10/19 MN034003EN

www.eaton.com

5

1 General information – EMS2 electronic motor starter

1.1 Standards

In addition to the standards in accordance with EN 60079 / VDE 165-1, 
separate standards for the corresponding types of protection apply to the 
protection of motors in potentially explosive atmospheres.

Motors with type of protection for potentially explosive areas, 
“increased safety”

The standard EN 60079-7 requires additional measures in the case of motors 
with the type of protection for potentially explosive areas, “increased 
safety”.

These measures ensure, with a high degree of certainty, that impermissible 
high temperatures, sparks and electric arcs are prevented on motors where 
these would not usually occur during normal operation.
The motor protection devices for this, which themselves are not located in a 
potentially explosive area, must be certified by an accredited admission 
office.

Motors in potentially explosive dust-air mixtures

For motors in potentially explosive dust-air mixtures, the standard 
EN 60079-14 specifies additional measures.

Directive 2014/34/EC (ATEX) on the approximation of the laws of the 
Member States concerning devices and protective systems intended for use 
in potentially explosive areas has been in force since 20.04.2016.

Содержание EMS-2






























































Отзывы: