Eaton EFX48 e-Fuse Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 161

background image

EFX48-xx Series with RM3-340/440 Installation and Operation Guide

16

Copyright © 2019 Eaton Corporation. All Rights Reserved.

IPN March 2019

Consignes de sécurité relatives aux ateliers d'énergie et leurs composants

Avertissements de sécurité

Conservez ces instructions. Ce manuel contient des informations de sécurité importantes pour le transport,
le déballage, l'installation et l'utilisation de tous les ateliers d'énergie courant continu Eaton.

Important

Si vous ne parvenez pas à comprendre l'ensemble du manuel fourni avec l 'atlier d'énergie courant continu,
veuillez contacter votre représentant Eaton avant de commencer toute manipulation, installation ou
utilisation. Vous trouverez ses coordonnées dans la section Assistance mondiale.

Public c concerné

Le présent guide est destiné aux personnes suivantes :

Les installateurs compétents dans :

•

l'installation et la mise en service d 'ateliers d'énergie courant continu

•

les conditions de sécurité au travail pour les équipements alimentés en courant alternatif et courant

continu

•

la réglementation relative à la sécurité électrique et les normes de câblage applicables localement

Les opérateurs et le personnel de maintenance compétents dans :

•

l'utilisation des systèmes d'alimentation en courant continu

•

les conditions de travail en sécurité pour les équipements alimentés en courant alternatif et courant

continu

Signaler des problèmes liés au présent manuel

Veuillez utiliser cette adresse e-mail pour signaler tout problème rencontré avec le présent guide :

Communication marketing produits courant continu Eaton

E-mail :

[email protected]

Pour plus d'informations et une assistance technique

Pour plus d'informations et une assistance technique, reportez-vous à la section Assistance mondiale.

Mises en garde

La présente section contient des avertissements importants. Lisez ces avertissements avant d'installer ou
d'utiliser un système d'alimentation courant continu Eaton.

Sécurité électrique

•

Tout système d'alimentation courant continu d'Eaton non pré-installé dans une armoire doit
être monté dans une armoire fermée répondant aux exigences de sécurité et de coffrets
coupe-feu, tel que spécifié dans les normes AS/NZS 60950.1 et EN 60950-1.

«
...
14
15
16
17
18
...
»

Содержание EFX48 e-Fuse Series


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EFX48 e-Fuse Series

Бренд: Value Point Страницы: 7

Бренд: Abus Страницы: 12

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Calsense Страницы: 74

Бренд: rada Страницы: 16

Бренд: GBD Страницы: 15

Бренд: Yealink Страницы: 8

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 24

PersonalWorkplace Pro Video

Бренд: G&D Страницы: 56

Бренд: Beninca Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды